DeltaDirect for iPad

Configure and tune using a fast, powerful combination of AudioCore and DeltaDirect, our bespoke iPad app.

DeltaDirect connects to your WiFi network and to your DPA amplifiers via a wireless router.  All amplifiers must be connected via their Ethernet control port to the router, and we recommend that there is a DHCP Server on the system to issue IP addresses automatically (this is normally the case and most routers have this feature built-in – Ethernet switches may not so check the specs!)

Once the app is opened and on-line (pressing the on-line button does this!)  the amplifiers will be sending out identity messages and the app will recognise these and inform that an amp (or a number of amps) are available to connect.  Once connected, all the amps appear on the default “All Devices” view.  The left hand icon on the amp’s panel can be touched to reveal more info and adjust a selection of device properties including its name, standby switching, AES switching, bridging modes, and network output source selection (if audio network card is fitted).

Touching an amplifier panel will open it up for editing:

Mute buttons directly mute outputs (if a meter is outlined in red it is muted elsewhere by a group mute).  The inputs are shown on the left of the screen, and the outputs are arranged in two banks fo four on the right – main power amp DSP channels, then aux line level output DSP channels.  Input channel sources are accessed though the Gain buttons, and output polarity is accessed though the output Gain buttons.  Delay and Limit buttons access input or output delays  (polarity switching is additionally shown on output delays tabs), with Limit opening the RMS and Peak Limiters (plus auto time constants selection – across outputs or auxes in a bank of four).  Filters will open a channel’s EQ for editing…

Individual bands may be edited by touching them in the table and directly moving slides or typing in values.  On outputs, the crossover filters are accessed at the bottom of the table.  Bypassed bands numbers are grey (like 3, 8 and 9 above).  Touch the options top right on the window to reset all bands and access copy and paste.

Touch the response graph to open full screen filter editing…

Drag filter nodes to adjust frequency and gain.  Pinch to adjust filter ‘Q’.  Touch the filter information above the graph to edit directly with sliders and numeric input.  Touch options (top right) to reset a band, all bands and change what’s shown – channel gain offset, Xovers included, phase response.  Also, select Autolock to move in one axis only when sweeping curves – start moving vertically (adjusting a filter gain) and the frequency will lock and vice versa.

Touch routing matrix to access routing, channel ganging and channel naming.  Full matrix mode can also be enabled independently for the power amplifier channels and aux channels.

Advanced grouping architecture can be directly configure from the app, and grouping information is stored in the amplifiers so can be retrieved when reconnecting.  Touch the options in the top right of the devices screen to select “Configure Grouping”:

32 absolute groups and 32 relative groups are available.  Absolute groups control multiple channels’ EQ at once, and all will track identically.  Input and output channels cannot be mixed in a group.  Relative groups control the gains, delays and limiters (outputs only) by applying relative offsets to all group members so they maintain their gain and delay relationships.  Limiter thresholds can only be adjusted down from their original settings (i.e. threshold lowered for more protection).

Groups appear below the devices on the main screen.  Absolute groups have an “A” top left, relative groups have an “R”. Touch a group to see its members (dots above channels on devices).  Controls for the group appear above the devices and can be directly edited.  Muting a relative group will make the group button turn red.  Meters outlined in red indicate that they are muted at an individual output level.

Back in the device view, grouping is shown beside channel names, and channels in an absolute group cannot have EQ directly editing here.  Channels in relative groups (a channel can be in multiple relative groups) can still have their gain, delay and if an output, limiter threshold changed, and any additional offset is shown in brackets beside the readout.  This value will be the aggregated value of all group memberships’ offsets.  Channel meters outlined in red show that this channel is muted by a group.